DRE cannot initialize its USB circuits. The DRE is not functional. [SI-9] This error occurs when the DRE is unable to successfully initialize its USB circuits and thus cannot transfer image data. The error is declared by the MCS and a log message is generated. The error can be caused by a disconnected or faulty USB cable or by a problem in the USB circuits in the DRE computer or by a problem in the datapath board. The error will probably result in a service call. The error clears only when power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. The MCS reported a hard drive read/write failure. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] This error occurs when the MCS application reports that it has detected an error while attempting to read or write from its storage space on the hard drive. The error clears only when power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. MCS printer configuration is incompatible with model hardware. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] This error occurs when the MCS application reports that the printer configuration is incompatible with the hardware model information. The error clears only when power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. The software for one or more micros is incompatible with the MCS version. Printer is unable to print films. The spooler is still able to accept jobs but new films will not be initiated. Films in progress will not be completed. [SI-3] This error occurs during MCS diagnostics when the MCS determines that the software version of one or more of the microcontrollers is incompatible with the MCS software version. This error should only happen when the MCS software is being installed or updated. The error is cleared when MCS diagnostics passes. --Shut down the imager, then start the imager. --If the error persists, call for service. Imager is open during self-test. Printer is unable to print films. The spooler is still able to accept jobs but new films will not be initiated. Films in progress will not be completed. [SI-3] This error occurs during MCS diagnostics when the imager determines that the hood or a cover was opened during the execution of Self Test. The error clears only when power is cycled. --Close the open imager hood or the open cover. --Shut down the imager, then start the imager. --If the error persists, call for service. The imager requires processor filter maintenance and cleaning. None - the system will function normally. [SI-0] This notification is written to the log when the processor filter maintenance (PFM) sheet count exceeds the PFM sheet count limit. Note: This notification is shown to the user, but is differentiated from other 'errors' because it is a special situation. See Local Panel and Web Portal User Interface design specifications for details. --None The imager requires preventive maintenance and system cleaning. None - the system will function normally. [SI-0] This notification is written to the log when the preventive maintenance (PM) sheet count exceeds the preventive maintenance/system cleaning sheet count limit. Note: This notification is shown to the user, but is differentiated from other 'errors' because it is a special situation. See Local Panel and Web Portal User Interface design specifications for details. --None The imager has been put into Service Mode. Printer is unable to print films. The spooler is still able to accept jobs but new films will not be initiated. Films in progress will not be completed. [SI-3] This auxiliary code indicates that the imager entered Service Mode. --None The imager hood has been opened. Printer is unable to print films. The spooler is still able to accept jobs but new films will not be initiated. Films in progress will not be completed. [SI-3] This auxiliary code indicates that the imager hood or cover was opened. --None One of the film supplies has no film tray. Printer is unable to print films. The spooler is still able to accept and queue jobs, but new films will not be initiated. This auxiliary code indicates that one of the film supplies has no film tray inserted. --None Undeliverable job is queued. None - the system will function normally. [SI-0] This auxiliary code indicates that one or more jobs are present in the Undeliverable Job queue. These jobs are fatally failed, and will remain in queue until they are removed by the user (via the Imager's setup reset screen, Web Portal, or Service Tool). (Restarting the imager does NOT delete these jobs.) Once the jobs are removed, the code is no longer displayed. --None DICOM connection is offline. The system is unable to queue new jobs for printing. It can still print jobs already queued. This auxiliary code indicates that the DICOM network connection to the imager is offline. (Note: The LED associated with the network button on the Imager's Local Panel will be off when this code is present.) The user can place the network back online by using the network button from the Imager's Local Panel. This will cause the code to no longer be displayed. --None User-initiated system restart Printer is unable to print films. This auxiliary code indicates that a user-initiated system restart is in-process. The user should not power the imager off during the startup sequence. The user should wait for the imager to complete its startup sequence, whereupon the code will no longer display. Note: One of the reasons that the operating system would be restarted is due to a software update procedure. --None User-initiated system shutdown is complete - power off required. Printer is unable to print films. This auxiliary code indicates that a user-initiated system shutdown is complete. (The shutdown would have been initiated remotely from the Web Portal or Service Tool, since shutting the imager off at the machine accomplishes the power off without initiating a shutdown.) The imager must now be powered-off using the power button located on the right side panel. When this code is displayed, the only way to restart the machine is to power off via the power button, then power back on. --None The MCS has detected a data transfer count error in the image data transfer from the DRE to the DPB. None - the system will function normally. [SI-0] This notification occurs when the wrong number of pixels is transferred between the DRE and the DPB in the allotted timeframe. The faulty image will be printed. The job will be failed, temporarily place in the undelivered queue, and rescheduled for delivery. (Note: Error 20-915 is generated when this problem is detected on the 3rd successive film.) --None The MCS has detected multiple successive data transfer count errors in the image data transfer from the DRE to the DPB. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] This error occurs when the wrong number of pixels is transferred between the DRE and the DPB in the allotted timeframe on 3 successive films. A faulty image is printed on each failure. Jobs associated with the faulty image will be failed, temporarily placed in the undelivered queue, and rescheduled for delivery. The error is cleared when the imager power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. The DRE initiated but did not complete rendering of image data. Printer is unable to print films. The spooler is still able to accept and queue jobs, but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] This error occurs when image data transfer between the DRE and the MCS is interrupted and does not complete within a reasonable time. The error is cleared when the imager power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. A failure, which is specified in greater detail by the primary error code, has occurred on this supply. None - the system will function normally. [SI-0] This auxiliary code indicates that the supply needs attention due to a failure. The failure information is specified by a separate error code. --None The film in the supply does not have a matching film model available, and must be calibrated in order to use. None - the system will function normally. [SI-0] This auxiliary code indicates that the film in the upper supply needs calibration before it can be used. --None The last calibration done for the film did not produce results within the normal range. None - the system will function normally. [SI-0] This auxiliary code indicates that the supply is operating in 'manual' mode, which means that the image quality is not within the normal range. --None The film is still inside the film bag or the film saver is still applied. None - the system will function normally. [SI-0] The film bag or the film saver has not yet been removed. The film cannot be used for printing until it is removed. --None The film saver must be applied before the film tray is unlocked for removal. None - the system will function normally. [SI-0] The film saver has not yet been applied. The film tray will not be unlocked for removal until the saver is applied, in order to prevent film exposure. The film tray can be manually unlocked if the film saver detection is not working properly. --None The error occurs during film pickup, when either the lift failed or the film was dropped during lifting. One or more feed magazine(s) is unable to print. The spooler is still able to accept and queue jobs and continue printing from any other available supply tray. [SI-2] This error occurs if, on the third successive attempt, the imager fails to pick up a sheet of film as indicated by the Film Separated sensor (S3x), the Pickup Home Sensor (S1x), or the Contact Sensor (S2x). The film has most likely fallen back down onto the tray. The error is cleared when a film tray is re-inserted after being removed. --Cover the film tray with the film saver. Remove the tray from the imager. Remove any misplaced films from Area 1. --If Area 1 did not contain misplaced films, take the film tray to a dark room and remove the film saver. Remove any misplaced films and cover the tray with the film saver. --Re-insert the film tray and remove the film saver. The film pickup assembly failed to pickup a sheet of film on the first attempt. None - the system will function normally. [SI-0] This notification occurs if the imager fails to pick up a sheet of film as indicated by the Film Separated sensor (S3x) or the Pickup Home Sensor (S1x). (Note: Error 2x-116 is generated on the third successive failed pickup attempt.) --None The film pickup assembly failed to reach its home position, or failed to go off home, or reached home unexpectedly. One or more feed magazine(s) is unable to print. The spooler is still able to accept and queue jobs and continue printing from any other available supply tray. [SI-2] This error occurs if the pickup fails to leave the home position at the beginning of a pickup cycle or fails to reach the home position at the end of a pickup cycle (as indicated by the pickup home sensor S1x). It can also occur if the pickup did not go off-home or reached home unexpectedly. This error can indicate a problem with sensor S1x or motor M3x. The error is cleared when a film tray is re-inserted after being removed. --Cover the film tray with the film saver. Remove the tray from the imager. --Re-insert the film tray and remove the film saver. --If the error persists, call for service. The film contact sensor failed to actuate as expected. One or more feed magazine(s) is unable to print. The spooler is still able to accept and queue jobs and continue printing from any other available supply tray. [SI-2] This error occurs only while attempting to pick up a film or checking for film in the tray. After the pickup home sensor (S1x) confirmed that the pickup assembly had left its home position, the film contact sensor (S2x) did not confirm that film contact was made. This error can also occur when the contact sensor was active when the pickup was at home, or when the contact sensor is stuck on. The most likely cause of the error is a failed contact sensor (S2x). The error is cleared when a film tray is re-inserted after being removed. --Cover the film tray with the film saver. Remove the tray from the imager. --Re-insert the film tray and remove the film saver. --If the error persists, call for service. The film separation sensor failed to actuate as expected. One or more feed magazine(s) is unable to print. The spooler is still able to accept and queue jobs and continue printing from any other available supply tray. [SI-2] This error occurs only while attempting to pick up a film. The pickup cups were lowered onto the film and the suction was applied, but the film separation sensor (S3x) did not actuate. The error is cleared when a film tray is re-inserted after being removed. --Cover the film tray with the film saver. Remove the tray from the imager. --Take the film tray to a dark room and remove the film saver. Verify that the film is lying flat. Replace the film saver. --Re-insert the film tray and remove the film saver. --If this error repeats, try a new film pack. 5. If the error persists, call for service. The feed roller failed to open/close as expected. One or more feed magazine(s) is unable to print. The spooler is still able to accept and queue jobs and continue printing from any other available supply tray. [SI-2] This error occurs if the feed roller nip sensor (S4) does not change from blocked to unblocked when opening or from unblocked to blocked when closing. Most likely cause is the motor (M1) did not turn or the sensor didn’t detect the motion. The error is cleared when a film tray is re-inserted after being removed. --Cover the film tray with the film saver. Remove the tray from the imager. --Re-insert the film tray and remove the film saver. --If the error persists, call for service. The media is jammed at the specified feeder. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] This error occurs if the leading edge of the film does not reach the Start of Page (SOP) sensor (S8) as a result of being fed from the supply to the exposure assembly. The film is likely still partially in the supply. The error is cleared when a film tray is re-inserted after being removed or the hood is closed. --Cover the film tray with the film saver. Remove the tray from the imager. Remove any misplaced films from Area 1. --If Area 1 did not contain misplaced films, take the film tray to a dark room and remove the film saver. Remove any misplaced films and replace the film saver. --If misplaced films were not found in the tray, open and close the imager hood. Wait 2 minutes for misplaced films to emerge from the imager. --Re-insert the film tray and remove the film saver. 5. If misplaced films were never located and this error recurs on the next film, follow the Side Access film clearing instructions. The film did not arrive at the SOP sensor on the first attempt of a film feed. None - the system will function normally. [SI-0] This notification occurs if the leading edge of the film does not reach the Start of Page (SOP) sensor (S8) as a result of being fed from the supply to the exposure assembly. The film may not have gone into the feed rollers, so the entire pickup/feed sequence will be restarted for 1 retry. If the retry subsequently fails, then error 26-325 will be generated, as well as either a 2x-116 or 2x-126 error. --None The film separation sensor is stuck on. One or more feed magazine(s) is unable to print. The spooler is still able to accept and queue jobs and continue printing from any other available supply tray. [SI-2] This error occurs only while attempting to pick up a film. The film separation sensor (S3x) is in an incorrect state for pickup is in home position, prior to film lift. The error is cleared when a film tray is re-inserted after being removed. --Cover the film tray with the film saver. Remove the tray from the imager. --Re-insert the film tray and remove the film saver. --If the error persists, call for service. The film failed to release from the cups once it was lifted. One or more feed magazine(s) is unable to print. The spooler is still able to accept and queue jobs and continue printing from any other available supply tray. [SI-2] This error occurs only while attempting to pick up a film. The film separation sensor (S3x) indicates that the film has not released from the cups at the end of the film pickup cycle. The error is cleared when a film tray is re-inserted after being removed. --Cover the film tray with the film saver. Remove the tray from the imager. --Re-insert the film tray and remove the film saver. --If the error repeats, restart the imager. --If the error persists, call for service. Printer is unable to read or write to the RF tag in the film pack. One or more feed magazine(s) is unable to print. The spooler is still able to accept and queue jobs and continue printing from any other available supply tray. [SI-2] The imager attempts to read the RF tag in the film pack at powerup and when a film tray is inserted. It attempts to write a new sheet count to the tag after successful film feed. The error is generated if invalid data is read or if the write fails. (If no data is read after 10 consecutive attempts, no error is generated and the film tray is reported empty.) The error is cleared when a film tray is re-inserted after being removed. --Try a different film pack. --If the error persists, call for service. The RF tag indicates that the specified film pack contains media that is incompatible with the imager. One or more feed magazine(s) is unable to print. The spooler is still able to accept and queue jobs and continue printing from any other available supply tray. [SI-2] The imager obtains the media type and CE mark information from the RF Tag when the film tray is loaded or when the imager power is turned on. This error occurs if the imager does not support the type at all. It also occurs if the imager has been configured (via the service tool) to reject the type or CE mark. The error is cleared when a film tray is re-inserted after being removed. --The imager has not been configured to use this film type. --Try a different film type or reconfigure the imager. --If the error persists, call for service. The RF tag indicates that the film pack contains media of a size that is incompatible with the imager. One or more feed magazine(s) is unable to print. The spooler is still able to accept and queue jobs and continue printing from any other available supply tray. [SI-2] The imager obtains the media size information from the RF Tag when the film tray is loaded or when the imager power is turned on. This error occurs if the imager does not support the size. The error is cleared when a film tray is re-inserted after being removed. --The imager has not been configured to use this film size. --Try a different film size or reconfigure the imager. --If the error persists, call for service. Received densitometer data from a calibration print which is not monotonically increasing. One or more feed magazine(s) is unable to print. The spooler is still able to accept and queue jobs and continue printing from any other available supply tray. [SI-2] This error occurs when the density readings that come from the calibration print are not monotonic or the densitometer did not find exactly 21 steps in the calibration wedge. Refer to GSM Theory of Operation for details. The most likely cause is fogged or expired film. The error is cleared when a film tray is re-inserted after being removed. --Try a different film pack. --If the error repeats, restart the imager. --If the error persists, call for service. Dmin requirement was not met on the specified calibration print. None - the system will function normally. [SI-0] The error occurs when the calibration sheet does not have a step density at or below the required Dmin value. Refer to GSM Theory of Operation for the Dmin requirement. The most likely causes are expired film or incorrect processor temperature. The error is cleared when a new calibration is initiated or when the film tray is removed. Any tray using these calibration results will automatically go into AIQC-Manual Mode and will continue printing but with reduced range in achievable densities. A new calibration will be attempted when this tray is re-inserted. --The minimum density of the film is too high. Calibration results for this film are outside the normal range, but will still be used. --If you do not wish to use these calibration results, perform a new calibration on this film or try another film pack. Dmax requirement was not met on the specified calibration print. None - the system will function normally. [SI-0] The error occurs when the calibration sheet does not have a step density at or above the required Dmax value. Refer to GSM Theory of Operation for the Dmax requirement. The most likely causes are expired film or incorrect processor temperature. The error is cleared when a new calibration is initiated or when the film tray is removed. Any tray using these calibration results will automatically go into AIQC-Manual Mode and will continue printing but with reduced range in achievable densities. A new calibration will be attempted when this tray is re-inserted. --The maximum density of the film is too low. Calibration results for this film are outside the normal range, but will still be used. --If you do not wish to use these calibration results, perform a new calibration on this film or try another film pack. A failure, which is specified in greater detail by the primary error code, has occurred on this supply. None - the system will function normally. [SI-0] This auxiliary code indicates that the supply needs attention due to a failure. The failure information is specified by a separate error code. --None The film in the supply does not have a matching film model available, and must be calibrated in order to use. None - the system will function normally. [SI-0] This auxiliary code indicates that the film in the upper supply needs calibration before it can be used. --None The last calibration done for the film did not produce results within the normal range. None - the system will function normally. [SI-0] This auxiliary code indicates that the supply is operating in 'manual' mode, which means that the image quality is not within the normal range. --None The film is still inside the film bag or the film saver is still applied. None - the system will function normally. [SI-0] The film bag or the film saver has not yet been removed. The film cannot be used for printing until it is removed. --None The film saver must be applied before the film tray is unlocked for removal. None - the system will function normally. [SI-0] The film saver has not yet been applied. The film tray will not be unlocked for removal until the saver is applied, in order to prevent film exposure. The film tray can be manually unlocked if the film saver detection is not working properly. --None The error occurs during film pickup, when either the lift failed or the film was dropped during lifting. One or more feed magazine(s) is unable to print. The spooler is still able to accept and queue jobs and continue printing from any other available supply tray. [SI-2] This error occurs if, on the third successive attempt, the imager fails to pick up a sheet of film as indicated by the Film Separated sensor (S3x), the Pickup Home Sensor (S1x), or the Contact Sensor (S2x). The film has most likely fallen back down onto the tray. The error is cleared when a film tray is re-inserted after being removed. --Cover the film tray with the film saver. Remove the tray from the imager. Remove any misplaced films from Area 1. --If Area 1 did not contain misplaced films, take the film tray to a dark room and remove the film saver. Remove any misplaced films and cover the tray with the film saver. --Re-insert the film tray and remove the film saver. The film pickup assembly failed to pickup a sheet of film on the first attempt. None - the system will function normally. [SI-0] This notification occurs if the imager fails to pick up a sheet of film as indicated by the Film Separated sensor (S3x) or the Pickup Home Sensor (S1x). (Note: Error 2x-116 is generated on the third successive failed pickup attempt.) --None The film pickup assembly failed to reach its home position, or failed to go off home, or reached home unexpectedly. One or more feed magazine(s) is unable to print. The spooler is still able to accept and queue jobs and continue printing from any other available supply tray. [SI-2] This error occurs if the pickup fails to leave the home position at the beginning of a pickup cycle or fails to reach the home position at the end of a pickup cycle (as indicated by the pickup home sensor S1x). It can also occur if the pickup did not go off-home or reached home unexpectedly. This error can indicate a problem with sensor S1x or motor M3x. The error is cleared when a film tray is re-inserted after being removed. --Cover the film tray with the film saver. Remove the tray from the imager. --Re-insert the film tray and remove the film saver. --If the error persists, call for service. The film contact sensor failed to actuate as expected. One or more feed magazine(s) is unable to print. The spooler is still able to accept and queue jobs and continue printing from any other available supply tray. [SI-2] This error occurs only while attempting to pick up a film or checking for film in the tray. After the pickup home sensor (S1x) confirmed that the pickup assembly had left its home position, the film contact sensor (S2x) did not confirm that film contact was made. This error can also occur when the contact sensor was active when the pickup was at home, or when the contact sensor is stuck on. The most likely cause of the error is a failed contact sensor (S2x). The error is cleared when a film tray is re-inserted after being removed. --Cover the film tray with the film saver. Remove the tray from the imager. --Re-insert the film tray and remove the film saver. --If the error persists, call for service. The film separation sensor failed to actuate as expected. One or more feed magazine(s) is unable to print. The spooler is still able to accept and queue jobs and continue printing from any other available supply tray. [SI-2] This error occurs only while attempting to pick up a film. The pickup cups were lowered onto the film and the suction was applied, but the film separation sensor (S3x) did not actuate. The error is cleared when a film tray is re-inserted after being removed. --Cover the film tray with the film saver. Remove the tray from the imager. --Take the film tray to a dark room and remove the film saver. Verify that the film is lying flat. Replace the film saver. --Re-insert the film tray and remove the film saver. --If this error repeats, try a new film pack. 5. If the error persists, call for service. The feed roller failed to open/close as expected. One or more feed magazine(s) is unable to print. The spooler is still able to accept and queue jobs and continue printing from any other available supply tray. [SI-2] This error occurs if the feed roller home sensor (S4) does not change from unblocked to blocked when opening or from blocked to unblocked when closing. Most likely cause is the motor (M1) did not turn or the sensor didn’t detect the motion. The error is cleared when a film tray is re-inserted after being removed. --Cover the film tray with the film saver. Remove the tray from the imager. --Re-insert the film tray and remove the film saver. --If the error persists, call for service. The media is jammed at the specified feeder. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] This error occurs if the leading edge of the film does not reach the Start of Page (SOP) sensor (S8) as a result of being fed from the supply to the exposure assembly. The film is likely still partially in the supply. The error is cleared when a film tray is re-inserted after being removed or the hood is closed. --Cover the film tray with the film saver. Remove the tray from the imager. Remove any misplaced films from Area 1. --If Area 1 did not contain misplaced films, take the film tray to a dark room and remove the film saver. Remove any misplaced films and replace the film saver. --If misplaced films were not found in the tray, open and close the imager hood. Wait 2 minutes for misplaced films to emerge from the imager. --Re-insert the film tray and remove the film saver. 5. If misplaced films were never located and this error recurs on the next film, follow the Side Access film clearing instructions. The film did not arrive at the SOP sensor on the first attempt of a film feed. None - the system will function normally. [SI-0] This notification occurs if the leading edge of the film does not reach the Start of Page (SOP) sensor (S8) as a result of being fed from the supply to the exposure assembly. The film may not have gone into the feed rollers, so the entire pickup/feed sequence will be restarted for 1 retry. If the retry subsequently fails, then error 26-325 will be generated, as well as either a 2x-116 or 2x-126 error. --None The film separation sensor is stuck on. One or more feed magazine(s) is unable to print. The spooler is still able to accept and queue jobs and continue printing from any other available supply tray. [SI-2] This error occurs only while attempting to pick up a film. The film separation sensor (S3x) is in an incorrect state for pickup is in home position, prior to film lift. The error is cleared when a film tray is re-inserted after being removed. --Cover the film tray with the film saver. Remove the tray from the imager. --Re-insert the film tray and remove the film saver. --If the error persists, call for service. The film failed to release from the cups once it was lifted. One or more feed magazine(s) is unable to print. The spooler is still able to accept and queue jobs and continue printing from any other available supply tray. [SI-2] This error occurs only while attempting to pick up a film. The film separation sensor (S3x) indicates that the film has not released from the cups at the end of the film pickup cycle. The error is cleared when a film tray is re-inserted after being removed. --Cover the film tray with the film saver. Remove the tray from the imager. --Re-insert the film tray and remove the film saver. --If the error repeats, restart the imager. --If the error persists, call for service. Printer is unable to read or write to the RF tag in the film pack. One or more feed magazine(s) is unable to print. The spooler is still able to accept and queue jobs and continue printing from any other available supply tray. [SI-2] The imager attempts to read the RF tag in the film pack at powerup and when a film tray is inserted. It attempts to write a new sheet count to the tag after successful film feed. The error is generated if invalid data is read or if the write fails. (If no data is read after 10 consecutive attempts, no error is generated and the film tray is reported empty.) The error is cleared when a film tray is re-inserted after being removed. --Try a different film pack. --If the error persists, call for service. The RF tag indicates that the specified film pack contains media that is incompatible with the imager. One or more feed magazine(s) is unable to print. The spooler is still able to accept and queue jobs and continue printing from any other available supply tray. [SI-2] The imager obtains the media type and CE mark information from the RF Tag when the film tray is loaded or when the imager power is turned on. This error occurs if the imager does not support the type at all. It also occurs if the imager has been configured (via the service tool) to reject the type or CE mark. The error is cleared when a film tray is re-inserted after being removed. --The imager has not been configured to use this film type. --Try a different film type or reconfigure the imager. --If the error persists, call for service. The RF tag indicates that the film pack contains media of a size that is incompatible with the imager. One or more feed magazine(s) is unable to print. The spooler is still able to accept and queue jobs and continue printing from any other available supply tray. [SI-2] The imager obtains the media size information from the RF Tag when the film tray is loaded or when the imager power is turned on. This error occurs if the imager does not support the size. The error is cleared when a film tray is re-inserted after being removed. --The imager has not been configured to use this film size. --Try a different film size or reconfigure the imager. --If the error persists, call for service. Received densitometer data from a calibration print which is not monotonically increasing. One or more feed magazine(s) is unable to print. The spooler is still able to accept and queue jobs and continue printing from any other available supply tray. [SI-2] This error occurs when the density readings that come from the calibration print are not monotonic or the densitometer did not find exactly 21 steps in the calibration wedge. Refer to GSM Theory of Operation for details. The most likely cause is fogged or expired film. The error is cleared when a film tray is re-inserted after being removed. --Try a different film pack. --If the error repeats, restart the imager. --If the error persists, call for service. Dmin requirement was not met on the specified calibration print. None - the system will function normally. [SI-0] The error occurs when the calibration sheet does not have a step density at or below the required Dmin value. Refer to GSM Theory of Operation for the Dmin requirement. The most likely causes are expired film or incorrect processor temperature. The error is cleared when a new calibration is initiated or when the film tray is removed. Any tray using these calibration results will automatically go into AIQC-Manual Mode and will continue printing but with reduced range in achievable densities. A new calibration will be attempted when this tray is re-inserted. --The minimum density of the film is too high. Calibration results for this film are outside the normal range, but will still be used. --If you do not wish to use these calibration results, perform a new calibration on this film or try another film pack. Dmax requirement was not met on the specified calibration print. None - the system will function normally. [SI-0] The error occurs when the calibration sheet does not have a step density at or above the required Dmax value. Refer to GSM Theory of Operation for the Dmax requirement. The most likely causes are expired film or incorrect processor temperature. The error is cleared when a new calibration is initiated or when the film tray is removed. Any tray using these calibration results will automatically go into AIQC-Manual Mode and will continue printing but with reduced range in achievable densities. A new calibration will be attempted when this tray is re-inserted. --The maximum density of the film is too low. Calibration results for this film are outside the normal range, but will still be used. --If you do not wish to use these calibration results, perform a new calibration on this film or try another film pack. The RF Tag reader failed diagnostics. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] When the RF Tag reader is told to perform diagnostics and returns a diagnostics failure, the MCS commands a retry. This error is indicated if the microcontroller still indicates a diagnostics failure after 3 attempts. The error clears only when power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. The RF Tag microcontroller is no longer communicating with the MCS. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] This error occurs when the MCS tries to communicate with the microcontroller but receives no response to 5 attempts. The error clears only when power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. The RF Tag microcontroller did not respond to the MCS. None - the system will function normally. [SI-0] This notification occurs when the MCS tries to communicate with the microcontroller but receives no response. (Note: Error xx-931 is generated when this problem is detected on the 5th successive failed communication attempt.) --None The film is jammed in the exposure area. SOP sensor (S8) timed out before seeing leading edge of film. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] This error occurs if the leading edge is not detected at the SOP (Start of Page) sensor (S8) in a timely manner. This error commonly occurs in conjunction with 2x-126. If it occurs alone, it is most likely an electronics issue. The error is cleared when either film tray is removed and reinserted or when the hood is opened and then closed. --If this error occurred at the same time as 21-126 or 23-126, follow the instructions for 21-126 or 23-126. --If this error occurred alone, open and close the imager hood to clear the error. --If this error repeats, restart the imager. --If the error persists, call for service. The film is jammed in the processor area. SOP sensor (S8) timed out before seeing trailing edge of film. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] This error occurs if the trailing edge is not detected at the SOP (Start of Page) sensor (S8) after the film has entered the Exposure Transport area. The error is cleared when the hood is opened then closed. When this error occurs, the processor stops rotating and the heater is turned off. All films in the printer will be marked bad and reprinted automatically. --Open the imager hood. --Unlatch and open the processor cover. Carefully remove any films found in the processor. Close and latch the processor. --Close the imager hood. If film was not previously removed, the misplaced films will emerge from the imager within 2 minutes. The film is jammed between the SOP sensor (S8) at the entrance of the exposure area and the densitometer sensor. Densitometer film sensor (S11) timed out before seeing leading edge of film. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. All other films will be reprinted. This error occurs if the leading edge is not detected at the Film at Densitometer sensor (S11) after the film leaves the exposure area. The error is cleared when the imager's hood is opened then closed. When this error occurs, the processor stops rotating and the heater is turned off. All films in the printer will be marked bad and reprinted automatically. --Open the imager hood and remove any films in Area 3. --If no films were found, unlatch and open the processor cover. Carefully remove any films found in the processor. Close and latch the processor. --Close the imager hood. If film was not previously removed, the misplaced films will emerge from the imager within 2 minutes. The film is jammed at the densitometer. Densitometer film sensor (S11) timed out before seeing trailing edge of film. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. All other films will be reprinted. This error occurs if the trailing edge is not detected at the Film at Densitometer sensor (S11) as the film exits the densitometer. The error is cleared when the imager's hood is opened then closed. When this error occurs, the processor stops rotating and the heater is turned off. All films in the printer will be marked bad and reprinted automatically. --Remove any films jammed in the imager film exit (Area 3). --Open the imager hood and remove any films in Area 2. --Close the imager hood. The Film Path Controller board is no longer communicating with the MCS. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] This error occurs when the MCS tries to communicate with the microcontroller but receives no response to 5 attempts. The error clears only when power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. The Film Path Controller board did not respond to the MCS. None - the system will function normally. [SI-0] This notification occurs when the MCS tries to communicate with the microcontroller but receives no response. (Note: Error xx-931 is generated when this problem is detected on the 5th successive failed communication attempt.) --None The SMD Microcontroller is no longer communicating with the Film Path Microcontroller. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated . Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] This error occurs when the Film Path Microcontroller tries to communicate with one of the SMD Microcontrollers but receives no response to 5 attempts. The error clears only when power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. The SMD Microcontroller board did not respond to the Film Path Microcontroller. None - the system will function normally. [SI-0] This notification occurs when the Film Path Microcontrller tries to communicate with one of the SMD Microcontrollers but receives no response. (Note: Error xx-933 is generated when this problem is detected on the 5th successive failed communication attempt.) --None The optics module polygon is not rotating as expected. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] This error occurs when the polygon speed measured by the optics module microcontroller is out of range. The error clears only when power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. Optics calibration and diagnostics detected a power monitor offset that was outside the predefined valid range. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] This error occurs when the power monitor offset measured by the optics calibration and diagnostics is outside the predefined valid range. Reference the Optics Calibration and Diagnostics Theory of Operations. The error clears when a calibration is requested or power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. Optics calibration and diagnostics was not able to adjust the laser dynamic range within the predefined valid range. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] This error occurs when the laser dynamic range measured by the optics calibration and diagnostics is outside the predefined valid range after 5 successive adjustment attempts. Reference the Optics Calibration and Diagnostics Theory of Operations. The error clears when a calibration is requested or power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. Optics calibration and diagnostics detected a maximum power that was outside the predefined valid range. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] This error occurs when the maximum laser power measured by the optics calibration and diagnostics is outside the predefined valid range. Reference the Optics Calibration and Diagnostics Theory of Operations. The error clears when a calibration is requested or power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. Optics calibration and diagnostics detected that the calculated laser dynamic range was approaching the limits of predefined valid range. None - the system will function normally. [SI-0] This notification occurs when the laser dynamic range has been adjusted and its value is within 10% of the upper or lower limit of the adjustment range. --None Optics calibration and diagnostics detected a maximum power that was approaching the predefined valid limit. None - the system will function normally. [SI-0] This notification occurs when the maximum laser power measured by the optics calibration and diagnostics is approaching the predefined valid limit. Reference the Optics Calibration and Diagnostics Theory of Operations. --None Optics calibration could not adjust the laser power gain within limits. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] The laser power gain is measured using a voltage on the laser driver. This error occurs when the laser driver voltage cannot be adjusted to within limits by the optics calibration after 20 successive attempts. Reference the Optics Calibration and Diagnostics Theory of Operations. --Shut down the imager, then start the imager. --If the error persists, call for service. Spinner jitter diagnostic calculated jitter corrections outside of predefined valid range. Jitter correction was disabled. None - the system will function normally. [SI-0] The system measures the end of scan jitter caused by variations in the polygon. The system uses these measurements to correct for variations and improve end of scan jitter. This error will occur if these measurements are outside of a range of values. If this error occurs, jitter correction is disabled. The diagnostic disables correction by settings all facet corrections to a predefined value. These measurements fine tune the jitter seen at the end of scan and typically the presence or absence of jitter correction is difficult to observe. --None Optics hardware did not report start of page. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] This error occurs if the optics hardware does not report the start of page condition even though Start of Page (SOP) sensor (S8) did indicate the leading edge of the film has been detected. The image is likely blank, but the film is not jammed and can likely be transported out of the imager successfully. The error clears only when power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. Internal Optics problems. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] This error occurs when the Image Exposure does not complete in the required time for 3 successive films. The error is cleared when the imager power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. Internal Optics problems. None - the system will function normally. [SI-0] This notification occurs when the Image Exposure does not complete in the required time. The faulty image will be printed. The job will be failed, temporarily placed in the undelivered queue, and rescheduled for delivery. If this problem is detected on 3 successive films, error 27-650 is declared. --None The Optics is no longer communicating with the MCS. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] This error occurs when the MCS tries to communicate with the microcontroller but receives no response to 5 attempts. The error clears only when power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. The Optics did not respond to the MCS. None - the system will function normally. [SI-0] This notification occurs when the MCS tries to communicate with the microcontroller but receives no response. (Note: Error xx-931 is generated when this problem is detected on the 5th successive failed communication attempt.) --None The Processor reported a NVRAM failure. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] This error occurs when the microcontroller reports that it has detected an error while attempting to read or write from its NVRAM. The error clears only when power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. The temperature parameters read from Processor NVRAM are outside the allowable ranges. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated . Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] This error occurs during initialization when the setpoint or offset parameters read from NVRAM are outside their allowable values. This error is caused by loading incorrect parameters into NVRAM or by an NVRAM error. The error clears only when power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. The temperature calculated from the voltage measured by the RTD is nearly zero. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] This error can occur for many electro-mechanical reasons: RTD and connector leads touching, drum-slip-ring failure, condensation (cold machine in warm environment), failed component in analog-to-digital conversion circuitry on Processor board, etc. The error clears only when power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. The processor failed to warm up in the allotted time frame. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] There are three primary causes for this error: 1) The Processor measured temperature has not locked into +-0.15 degree C of setpoint for at least 20 seconds prior to the end of the warm-up time allotted. The Processor electronics has failed - replace board. For this case, the allotted time of warm-up shall have expired. 2) There was a failure to heat or the rate of warming up was too slow (at or less then 3 degrees C per minute). For this case, the failed SSR status bit should be set. Either the solid-state relay (SSR) or mechanical power relay has failed - replace board. 3) The environment may be too cold or the power source under-rated - repeat the warm-up cycle. The allotted time is calculated from the initial processor drum temperature. The error clears only when power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. The temperature calculated from the voltage measured by the RTD is the maximum possible. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] This error likely occurred in conjunction with the over heat error. The most likely cause is an open in the RTD circuit (RTD fractured, drum slip ring failure, wiring harness not connected, etc). The error clears only when power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. The heater has been turned on and the expected temperature rise has not been detected. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated . Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] There are three primary causes for this error: 1) The Processor measured temperature has not locked into +-0.15 degree C of setpoint for at least 20 seconds prior to the end of the warm-up time allotted. The Processor electronics has failed - replace board. For this case, the allotted time of warm-up shall have expired. 2) There was a failure to heat or the rate of warming up was too slow (at or less then 3 degrees C per minute). For this case, the failed SSR status bit should be set. Either the solid-state relay (SSR) or mechanical power relay has failed - replace board. 3) The environment may be too cold or the power source under-rated - repeat the warm-up cycle. The allotted time is calculated from the initial processor drum temperature. The error clears only when power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. The processor drum temperature exceeded the limit. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] This error occurs if the measured temperature is approximately 148 degrees C or greater. If there is no corresponding “Processor Open Circuit Error”, then the likely cause is a stuck on solid-state relay (SSR). The software shuts power off to the drum, but the redundant safety feature of the thermal circuit breaker in the drum may also trip (the drum thermal circuit breaker must be manually reset). The error clears only when power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. The Processor control board is no longer communicating with the MCS. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] This error occurs when the MCS tries to communicate with the microcontroller but receives no response to 5 attempts. The error clears only when power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. The Processor did not respond to the MCS. None - the system will function normally. [SI-0] This notification occurs when the MCS tries to communicate with the microcontroller but receives no response. (Note: Error xx-931 is generated when this problem is detected on the 5th successive failed communication attempt.) --None The Densitometer reported a NVRAM failure. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] This error occurs when the microcontroller reports that it has detected an error while attempting to read or write from its NVRAM. The error clears only when power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. The density sensor offset reading is out of range. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] During a calibration print and during densitometer diagnostics, a reading from the density sensor is taken with the light source turned off. The error is indicated if the microcontroller reports the reading out of range. The error clears only when power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. The density sensor reference reading is out of range Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] During a calibration print and during densitometer diagnostics, a reading from the density sensor is taken with the light source turned on. This error occurs when the reading is out of range. (Note: Notification 945 is generated when this reading is nearing the range limit.) The error clears only when power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. The fiducial sensor offset reading is out of range. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] During a calibration print and during densitometer diagnostics, a reading from the fiducial sensor is taken with the light source turned off. The error is indicated if the microcontroller reports the reading out of range. The error clears only when power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. The fiducial sensor reference reading is out of range. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] During a calibration print and during densitometer diagnostics, a reading from the fiducial sensor is taken with the light source turned on. This error occurs when the reading is out of range. (Note: Notification 947 is generated when this reading is nearing the range limit.) The error clears only when power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. The Densitometer board is no longer communicating with the MCS. Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] This error occurs when the MCS tries to communicate with the microcontroller but receives no response to 5 attempts. The error clears only when power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. The Densitometer did not respond to the MCS. None - the system will function normally. [SI-0] This notification occurs when the MCS tries to communicate with the microcontroller but receives no response. (Note: Error xx-931 is generated when this problem is detected on the 5th successive failed communication attempt.) --None The density sensor reference reading is approaching the limit None - the system will function normally. [SI-0] During a calibration print and during densitometer diagnostics, a reading from the density sensor is taken with the light source turned on. This notification occurs when the reading is outside of the optimal range, i.e. approaching the range limit. (Note: Error 925 is generated when this reading is over the range limit.) --None The fiducial sensor reference reading is approaching the limit None - the system will function normally. [SI-0] During a calibration print and during densitometer diagnostics, a reading from the fiducial sensor is taken with the light source turned on. This notification occurs when the reading is outside of the optimal range, i.e. approaching the range limit. (Note: Error 927 is generated when this reading is over the range limit.) --None The Local Panel board is no longer communicating with the MCS. The Local Panel User Interface will not display correct data. This error occurs when the MCS tries to communicate with the microcontroller but receives no response to 5 attempts. The error clears only when power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. The Local Panel did not respond to the MCS. None - the system will function normally. [SI-0] This notification occurs when the MCS tries to communicate with the microcontroller but receives no response. (Note: Error xx-931 is generated when this problem is detected on the 5th successive failed communication attempt.) --None The MCS is no longer communicating with the Local Panel Board. Unknown. If the MCS is down, the printer will not print films. If the problem is limited to communications, the printer may be able to print films. This error occurs when the Local Panel does not receive communications from the MCS. The Local Panel waits for 50 seconds, then generates a fake button press in an attempt to provoke communications from the MCS. After an additional 10 seconds, if the Local Panel has not received MCS communications, this error is displayed on the Local Panel User Interface. The error clears when the Local Panel detects MCS communications. --Shut down the imager, then start the imager. --If the error persists, call for service. Unknown. As this is an unexpected or unknown error, it is not possible to document specific details. A general, non-specific error has occurred in the Configuration and Control Subsystem. --None The system will continue to run normally, unless the subsystem or component in question cannot run any longer. When a subsystem or component generates a non-recoverable, Configuration-And-Control will attempt to shutdown and restart it. This error means that Configuration-And-Control has initiated more than the configured number of allowed restarts. --None Configuration-and-Control subsystem may not execute correctly. An error occurred while reading the Configuration-and-Control Subsystem configuration information. --None The subsystem in question will not be started. An error occurred while attempting to start a subsystem. --Restart the imager. --If the error persists, call for service. The subsystem in question may still be running, in which case full shutdown will not be achievable. An error occurred while attempting to stop a subsystem. --None Configuration-and-Control will attempt to re-establish communications with the subsystem in question. If communications is lost, the subsystem will be shutdown by force and restarted. An unknown error has occurred while communicating with a subsystem. --None None - the system will function normally. [SI-0] All subsystems to be started by the Configuration and Control Subsystem have been started. Note: This code will not be sent out as a message. --None None - the system will function normally. [SI-0] The operating system did not complete shutting down in the expected amount of time. Note: This code will not be sent out as a message. --None The subsystem will be temporarily unavailable until it is restarted by the Configuration and Control Subsystem. Depending on the subsystem, it may causes associations to be rejected, or printing to be delayed. A subsystem that was started by the Configuration and Control Subsystem terminated abnormally. Note: This code will not be sent out as a message. --None Unknown. As this is an unexpected or unknown error, it is not possible to document specific details. A general, non-specific error has occurred in the DICOM Input Print SCP Subsystem. --None The SCU will not be able to open an association, and therefore will not be able to deliver a print job. The maximum number of associations configured has been exceeded. The association is rejected. --None The SCU will not be able to open an association, and therefore will not be able to deliver a print job. The AE title did not map to a destination that currently available at this SCP. --None The SCU will not be able to open an association, and therefore will not be able to deliver a print job. An association request was rejected for one or more of the following reasons: 1. The SCU did not specify an implementation UID. 2. The SCU did not specify an application context name. 3. The protocol version is a two-byte field; bit ZERO (0) must be ONE (1). 4. The SCU did not specify any presentation context items to be negotiated. 5. None of the proposed presentation context items were successfully negotiated. This may happen, for example, when a DICOM Store SCU tries to communicate with a DICOM Print SCP. --None If a study is currently in progress, it cannot be completed. New studies will not be accepted. The partition of the disk where studies are stored is full. --Delete jobs in the "Unprintable jobs" queue. --Load requested film type for jobs in the "Waiting for media" queue. --If the error persists, call for service. The SCP will abort the association tied to this connection. The SCP may be configured to periodically send packets to maintain a TCP/IP connection with an SCU, to which the SCU should reply. This error means that the SCU did not reply to the SCP's "Are You There?" packet. --None The SCP will abort the association tied to this connection. The SCP has lost the network connection to an SCU. --None MIM Core will not process the current print job. The Referenced PLUT specified by tag (2050,0500) in the Film Box or Image Box is not present. --None The named SOP will not be processed. If the SOP is a film session or film box, the requested page(s) will not be printed. A required attribute for the specified SOP class is missing. For complete description of mandatory attributes in a SOP class, see [PART4]. --None The named SOP will not be processed. If the SOP is a film session or film box, the requested page(s) will not be printed. An invalid attribute for the specified SOP class was found. For complete description of valid attributes and their contexts, see [PART4]. --None Unknown. As this is an unexpected or unknown error, it is not possible to document specific details. An unknown error has occurred in the study reclamation subsystem. --None Study reclamation subsystem may not execute correctly An error occurred while reading the Study Reclamation Subsystem configuration information. --None Completed studies will be systematically removed from the system until the low-water mark is reached. Study reclamation has been initiated because either the high-water mark has been reached, or the scheduled time for study reclamation has occurred. --None None. MIM Core should continue to run normally, although this warning may continue to be logged periodically. The storage recovery subsystem could not reach the low-water mark while running the storage reclamation routines. --None None. Study reclamation has been completed because the low-water mark was successfully reached. --None None. Most likely, the entire system is shutting down. Also, it may be that a configuration information change that requires the subsystem to be restarted. The study reclamation subsystem has received a shutdown request. --None Unknown. As this is an unexpected or unknown error, it is not possible to document specific details. A general, non-specific error has occurred in the Delivery Subsystem. --None Jobs will not be delivered, as the software interface for the Delivery Subsystem could not be started. A general error occurred while starting the Delivery Subsystem. --None Delivery subsystem may not execute correctly. An error occurred while reading the Delivery Subsystem configuration information. --None The current job may not be processed to completion due to an internal error. The job delivery component has encountered a general error while processing a job. --None Jobs will not be delivered while the printer is in this state. The printer is not ready to accept delivery jobs. --None The submitted job will not be delivered. An error occurred while reading the Delivery Subsystem configuration information. --None The submitted job will not be delivered. The currently requested media is not available. --None None. Notification that a page was successfully delivered; this is not an error condition. --None None. Notification that a job was successfully delivered; this is not an error condition. --None The current job will not deliver. An error occurred while accessing the MIM Core database. The database may be corrupted, or simply a timeout occurred. --None The current job will not deliver. An error occurred in the destination business logic component. The database may be corrupted, or simply a timeout occurred. --None The current page will not be processed because it could not be rendered due to an internal error. A general page builder error has occurred. Conditions include: 1. performance timer errors, 2. dumping images at lower level, 3. error initializing text, line lists, or member variables --Delete jobs in the "Unprintable jobs" queue. --Resend the print job from the image source. --If the error persists, call for service. The current page will not be processed because it could not be rendered due to an internal error. The page builder component has encountered the following rendering error: 1. general rendering error. 2. in the final render call after all of the chains have been formed. 3. rendering trim lines, rectangles, etc. 4. rendering text. 5. rendering the indicator icon, including missing or corrupted icon data. 6. problem with algorithm parameter. --Delete jobs in the "Unprintable jobs" queue. --Resend the print job from the image source. --If the error persists, call for service. The current page will not be processed because it could not be rendered due to an internal error. The page builder component has encountered the following image data error: 1. width and/or height is less than zero, 2. bits beyond the pixel depth are not zeroed. --Delete jobs in the "Unprintable jobs" queue. --Resend the print job from the image source. --If the error persists, call for service. The current page will not be processed because rendering was aborted. The page builder component has been asked to halt a rendering that is currently in progress. --None The current page will not be processed because it could not be rendered due to an internal error. The page builder component has encountered the following data error: 1. the specified page width and/or height is less than zero. 2. the number of page bands is neither 1 nor 3, and each of the bands do not have the same type. 3. icon (x1,y1) and/or (x2,y2) is beyond the page extents. 4. image size mismatch error, where the size read does not match the size expected. 5. bad cropping coordinates. 6. icon or image file not found. 7. trying to read image data; most likely, the image input file could not be found. 8. general error accessing the database component. --Delete jobs in the "Unprintable jobs" queue. --Resend the print job from the image source. --If the error persists, call for service. The page builder has encountered one of the following errors while building the image processing chain: 1. general chain-building error. 2. tonescaling error, usually an error in the TFT, PLUT, or Curve Shape. 3. error forming the color processing chain, including missing ICC profile files. 4. layout chain error, including bad rotation and/or flip parameters. 5. error forming the printer processing chain. --Delete jobs in the "Unprintable jobs" queue. --Resend the print job from the image source. --If the error persists, call for service. None. The system will automatically compensate for the problem. The 12-bit image data had pixels that were greater than 12 bits. --None Job may not be delivered due to an internal error communicating with the MIS. One of the following internal errors has occurred: 1. Binding error. 2. Staging error. 3. Printing error. 4. Exposure error. 5. Unknown internal error. --None The current job will not be delivered until the specified media is loaded. The requested media is not currently loaded in the printer. --None The current job will not be delivered until the specified media has been calibrated The requested media is not calibrated. --None Jobs will not be delivered until the calibration cycle is completed. The requested media is currently being calibrated. --None Jobs may not be delivered since the media could not be calibrated. An error occurred during media calibration. --None The current job will not be delivered until the specified media is loaded. The requested media is empty. --None The current job will not be delivered until the media jam is cleared. The requested media is currently jammed. --None Unknown. As this is an unexpected or unknown error, it is not possible to document specific details. A general, non-specific error has occurred in the Delivery Subsystem. --None Internal software error in the MIS software. The DRE is not functional. [SI-9] This represents any of a number of errors that indicate that internal software functionality of the MCS Interface Server (MIS) subsystem has failed. Examples include: persistent memory failures, object creations failing, system call failures, missing configuration files. --Restart the imager. --If the error persists, call for service. Internal image memory buffer error in the MIS software. The DRE is not functional. [SI-9] This represents any of a number of errors that indicate that image memory buffer functionality of the MCS Interface Server (MIS) subsystem has failed. --Restart the imager. --If the error persists, call for service. Internal database access software error in the MIS software. Printer can accept jobs and print but cannot track total print counts, prints to PM, prints to Filter change, or the history of calibration data. This represents any of a number of errors indicating that database software functionality of the MCS Interface Server (MIS) subsystem has failed. Examples include: SQL server down, incorrect database table installation, database read/ write/ update failed. --Restart the imager. --If the error persists, call for service. Printer configuration is incompatible with system settings Printer is unable to print films. The spooler is still able to accept and queue jobs but new films will not be initiated. Films downstream of the affected subsystem will be completed. All other films will be reprinted. [SI-1] This error occurs when the MIS detects that the system settings are incompatible with the printer configuration. The error clears only when power is cycled. --Shut down the imager, then start the imager. --If the error persists, call for service. The MCS is not communicating with the MIS. Printer is unable to print films. The spooler is still able to accept jobs but new films will not be initiated. Films in progress will not be completed. [SI-3] This error occurs when the MCS fails to respond to the MIS. The error is declared by the MIS and a log message is generated. This error is a fatal error that will probably result in a service call. --Restart the imager. --If the error persists, call for service. Internal software error in the underlying Alert Link software which is used by service tool software and web portal software. Service Tool operations or Web Portal operations may not be working correctly. The DRE should be functional, but may not respond correctly to the service/portal function being run or the function may fail. An internal error attributable to software components used by Service Tool or Web Portal has occurred. (The Web Portal is based on the Service Tool software, so the source of this error is not differentiable.) This error code represents any of a number of errors indicating that internal software functionality of the Service Tool or Web Portal subsystem has failed. Examples include: persistent memory failures, object creations failing, system call failures, Common Service Platform (CSP) framework errors. --None